Descripció
Model de producte
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书2023-2.jpg)
Model: DH12S-LD
Equipament aplicable:crawler wire saw machine
Diagrama d'accessoris del producte
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书英文2023-2-1.jpg)
Nota: Podeu triar una de les tres antenes. L'antena amb ventosa és estàndard per defecte.
Descripció de l'interruptor del comandament a distància
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书英文2023-3-1.jpg)
Displaycontent introduction
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书英文2023-4.1-1.jpg)
Large motor speed:S1:0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书英文2023-4.2.jpg)
Baix voltatge: La bateria del comandament a distància és massa baixa, substituïu la bateria.
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书英文2023-4.3.jpg)
S'ha caigut la xarxa: El senyal sense fil s'interromp. Si us plau, comproveu la potència del receptor, enceneu-lo de nou, i reinicieu el comandament a distància.
Instruccions de funcionament de la funció de control remot
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, enceneu l'interruptor d'alimentació, andthe display will show the motor speed, indicant l'inici correcte.
2.Large motor and speed regulation
Turn the “forward/reverse” switch to forward, the receiver’s large motor will turn on, and the display will show forward![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书2023-5箭头.jpg)
Turn the “forward/reverse” switch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书2023-5-建头上.jpg)
Rotate the “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “forward/reverse” switch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward ![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书2023-5箭头.jpg)
Turn the “Forward/Reverse” switch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书2023-5-建头上.jpg)
4.Turn left and right
Turn the “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书2023-5-建头.jpg)
Turn the “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书2023-53.jpg)
5.Turn in place
In manual mode:
Turn left in place: Press and hold the “Enable” button, turn the “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Press and hold the “Enable” button, turn the “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” button and rotate the “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Automatic cutting
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In manual mode, press and hold the “Enable” button and rotate the “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 a 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (users are prohibited from modifying it without permission)
Algunes funcions del comandament a distància es poden ajustar mitjançant paràmetres. In manual mode, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Sortiu del menú de paràmetres: triar desar o no desar, then press the enable button to confirm the exit;
Maximum current: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, default 800, modification is prohibited;
Deceleration parameter: automatic cutting control parameter. When the cutting current change value exceeds this value,deceleration begins.
Acceleration a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Deceleration a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximum walking: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Speed limit offset: the maximum speed of the small motor during automatic cutting.
Maximum host: maximum speed of large motor.
Característiques elèctriques del comandament a distància
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书英文2023-6.jpg)
Mida del comandament a distància
![](https://www.wixhc.cn/wp-content/uploads/2023/11/履带绳锯机自动遥控器-DH12S-LD使用说明书英文2023-7.jpg)
El dret d'interpretació final d'aquest producte només pertany a la nostra empresa.
Ressenyes
Encara no hi ha comentaris.