履帶式繩鋸機全自動無線遙控DH12S-LD

MK3-M4

產品型號

模型: DH12S-LD

適用設備:crawler wire saw machine

產品配件圖

筆記: 您可以選擇三種天線之一. 預設標配吸盤天線.

遙控開關說明

顯示內容介紹

Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (參數可調)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

低電壓: 遙控器電池電量過低, 請更換電池.

網路斷線: 無線訊號中斷. 請檢查接收器功率, 再次打開電源, 並重新啟動遙控器.

遙控功能操作說明

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, 打開電源開關, andthe display will show the motor speed, 表示啟動成功.

2.Large motor and speed regulation

轉動 “前進/後退” 切換到轉發, the receiver’s large motor will turn on, and the display will show forward

轉動 “前進/後退” 切換到反向, the large motor of the receiver will turn on in reverse, and the display will show reverse

旋轉 “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move the “前進/後退” 切換到轉發, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

轉動 “前進/後退” 切換到反向, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

轉動 “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left

轉動 “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

手動模式下:
Turn left in place: 按住 “Enable” button, 轉動 “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: 按住 “Enable” button, 轉動 “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

In automatic mode: press and hold the “Enable” 按鈕並旋轉 “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;

7.自動切割

The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: 手動模式下, press and hold the “Enable” 按鈕並旋轉 “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 to 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (未經許可，禁止使用者修改)

Some functions of the remote control can be adjusted through parameters. 手動模式下, when the small motor speed S2 is 10, 連續向上推前進/後退開關3次, and then push it down three times in a row to enter the parameter menu;
退出參數選單: 選擇儲存或不儲存, then press the enable button to confirm the exit;
最大電流: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, 預設 800, 禁止修改;
加減速參數: automatic cutting control parameter. 當切削電流變化值超過此值時,deceleration begins.
加速度a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
減速度a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
最大步行距離: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
限速偏移: the maximum speed of the small motor during automatic cutting.
最大主機數: maximum speed of large motor.

遙控電氣特性

遙控器尺寸

本產品最終解釋權歸我司所有.