Sollicitatie:Speciaal gebruikt voor rupsdraadzaagmachines
1.Ondersteunt automatische snijmodus, past automatisch de loopsnelheid van de kleine motor aan volgens de grote motorstroom, en bereikt automatische snijcontrole.
2.Barrièrevrije transmissieafstand is 200 meter.
3. Ondersteunt dubbele snelheidsregeling voor grote motoren en kleine motoren.
4. Ondersteuning van kleine motor die op zijn plaats draait.
5. Ondersteunt lineaire correctie van de kleine motor van het linker- en rechterwiel.
Model: DH12S-LD
Toepasselijke apparatuur:crawler wire saw machine
Opmerking: Je kunt één van de drie antennes kiezen. De zuignapantenne is standaard standaard.
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters instelbaar)
Linear correction value: DF: -99-99 (1 unit is about 0.02V)
Lage spanning: De batterij van de afstandsbediening is te laag, Vervang de batterij.
Netwerk viel uit: Het draadloze signaal wordt onderbroken. Controleer het vermogen van de ontvanger, schakel het opnieuw in, en start de afstandsbediening opnieuw op.
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, zet de stroomschakelaar aan, andthe display will show the motor speed, wat een succesvolle opstart aangeeft.
2.Large motor and speed regulation
Draai de “vooruit/achteruit” overschakelen naar vooruit, the receiver’s large motor will turn on, and the display will show forward
Draai de “vooruit/achteruit” overschakelen naar achteruit, the large motor of the receiver will turn on in reverse, and the display will show reverse
Draai de “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “vooruit/achteruit” overschakelen naar vooruit, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Draai de “Vooruit/achteruit” overschakelen naar achteruit, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Draai de “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Draai de “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
In handmatige modus:
Turn left in place: Houd de knop ingedrukt “Enable” button, draai de “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Houd de knop ingedrukt “Enable” button, draai de “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In de automatische modus: press and hold the “Enable” knop en draai de “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Automatisch snijden
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In handmatige modus, press and hold the “Enable” knop en draai de “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 naar 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (Het is gebruikers niet toegestaan deze zonder toestemming te wijzigen)
Some functions of the remote control can be adjusted through parameters. In handmatige modus, when the small motor speed S2 is 10, druk de vooruit/achteruit-schakelaar drie keer achter elkaar omhoog, and then push it down three times in a row to enter the parameter menu;
Verlaat het parametermenu: choose to save or not save, then press the enable button to confirm the exit;
Maximale stroom: the operating rated current of the cutting motor is 80% of this currentt;
Speed Control Parameters: automatic cutting control parameters, standaard 800, wijziging is verboden;
Vertragingsparameter: automatic cutting control parameter. Wanneer de snijstroomveranderingswaarde deze waarde overschrijdt,deceleration begins.
Versnelling A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Vertraging A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Begin met zelfvergrendeling: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximaal lopen: the maximum speed of the small motor.
Snijstroom: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Standaardsnelheidslimiet: the default maximum speed of automatic cutting speed when turning on the machine.
Automatische modus: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Offset snelheidslimiet: the maximum speed of the small motor during automatic cutting.
Maximale gastheer: maximum speed of large motor.
Het uiteindelijke interpretatierecht van dit product behoort uitsluitend toe aan ons bedrijf.
