Omschrijving
Product Model
Model: DH12S-LD
Toepasselijke apparatuur:crawler wire saw machine
Diagram met productaccessoires
Opmerking: Je kunt één van de drie antennes kiezen. De zuignapantenne is standaard standaard.
Beschrijving van de afstandsbedieningsschakelaar
DisplayContent Inleiding
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (Parameters verstelbaar)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Lage spanning: De batterij van de afstandsbediening is te laag, Vervang de batterij.
Netwerk viel uit: Het draadloze signaal wordt onderbroken. Controleer het vermogen van de ontvanger, schakel het opnieuw in, en start de afstandsbediening opnieuw op.
Bedieningsinstructies voor de afstandsbedieningsfunctie
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, zet de stroomschakelaar aan, andthe display will show the motor speed, wat een succesvolle opstart aangeeft.
2.Large motor and speed regulation
Draai de “vooruit/omgekeerd” Schakel over naar vooruit, the receiver’s large motor will turn on, and the display will show forward
Draai de “vooruit/omgekeerd” Schakel over naar omgekeerd, the large motor of the receiver will turn on in reverse, and the display will show reverse
Draai de “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “vooruit/omgekeerd” Schakel over naar vooruit, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Draai de “Vooruit/omgekeerd” Schakel over naar omgekeerd, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Draai de “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Draai de “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
In handmatige modus:
Turn left in place: Houd de “Enable” button, draai de “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Houd de “Enable” button, draai de “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” knop en draai de “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Automatisch snijden
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In handmatige modus, press and hold the “Enable” knop en draai de “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 naar 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (Gebruikers mogen het zonder toestemming niet wijzigen)
Sommige functies van de afstandsbediening kunnen via parameters worden aangepast. In handmatige modus, when the small motor speed S2 is 10, Duw de voorwaartse/omgekeerde schakelaar drie keer achter elkaar omhoog, and then push it down three times in a row to enter the parameter menu;
Verlaat het parametermenu: kiezen om op te slaan of niet op te slaan, then press the enable button to confirm the exit;
Maximale stroom: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, standaard 800, Modificatie is verboden;
Vertragingsparameter: automatic cutting control parameter. Wanneer de waarde van de snijstroomwijziging deze waarde overschrijdt,deceleration begins.
Versnelling A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Vertraging A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximaal lopen: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Snelheidslimiet offset: the maximum speed of the small motor during automatic cutting.
Maximale gastheer: maximum speed of large motor.
Elektrische kenmerken van de afstandsbediening
Grootte afstandsbediening
Het uiteindelijke interpretatierecht van dit product behoort uitsluitend toe aan ons bedrijf.
