Njikwa ikuku ikuku CNC nwere mmemme PHB06B

Nkọwa

 

1.Nmkpọ Okwu mmalite

The programmable CNC remote control PHB06B is suitable for wireless
Ọrụ nchịkwa dịpụrụ adịpụ nke sistemụ CNC dị iche iche. It supports users to
customize programming and develop button functions to realize remote
control of various functions on the CNC system; it supports users to
customize programming and develop display content to realize dynamic
display of system status; the remote control comes with a rechargeable
battery and supports Type-C interface charging.

2.Ngosipụta ngwaahịa

1. Iji teknụzụ nkwukọrịta 433mhz, Ọrụ ikuku
anya bụ 80 mita;
2. Iji ọrụ na-eme ngwa ngwa, 32 setịpụrụ nke ikuku ikuku
Enwere ike iji ndị na-achị achị n'otu oge ahụ na-emetụta ibe ha;
3. ọ nwere ike na-akwado 32pcs equipments eji n'otu oge 12 Mbido akara omenala;
4. Support 2.8-inch screen, display content custom programming;
5. ọ nwere ike na-akwado 32pcs equipments eji n'otu oge 1 6-speed axis selection switch, which can be custom programmed;
6. ọ nwere ike na-akwado 32pcs equipments eji n'otu oge 1 7-speed magnification switch, which can be custom programmed;
7. ọ nwere ike na-akwado 32pcs equipments eji n'otu oge 1 electronic handwheel, 100 pulses/turn;
8. Support standard Type-C charging; 5Nkọwapụta V-2A; battery
specification 18650/12580mWh battery.

3.a na-ebelata ọnụego ọdịda USB

4. Nkọwapụta ngwaahịa

5.Mmepe mmeghe nke ngwaahịa

Ndetu：
①Power switch：
Control hand wheel to open and close

②Enable buttons on both sides：
The enabling button must be pressed to crank the hand wheel;

③Custom button area
12 buttons arranged in 3X4, Mmemme akọwapụtara;

④Axis selection, magnification switch
1 6-position axis selection switch, which can be customized and programmed;
1 7-position ratio switch, which can be customized and programmed

⑤ Emergency stop switch:
Handwheel emergency stop switch;

⑥Display area:
Can display current power, signal, and customized display content;

⑦Electronic hand wheel：
1 electronic handwheel, 100 pulses/turn.

⑧Charging port:

Built-in rechargeable battery, charged using Type-C charger, charging voltage 5V,
current 1A-2A; charging time 7 awa;

6.Product accessories diagram

7.Product Installation Guide

1. Insert the USB receiver into the computer, the computer will automatically
recognize and install the USB device driver without manual installation;
2. Insert the remote control into the charger. After the battery is fully charged, turn
on the power switch, turn on the remote control, and the display shows normal, which
means the power-on is successful;
3. After powering on, you can perform any button operation. The remote control can
support dual button operation at the same time. When you press any button, a black
square will appear next to the signal on the remote control, indicating that the button
is valid.

8.Product Operation Instructions
Before product development and use, you can use the Demo software we provide to test
the buttons and display of the remote control, or use the Demo as a reference routine for
future programming development;
Before using the Demo software, please plug the USB receiver into the computer, make
sure the remote controller has sufficient power, turn on the power switch, and then use it;
Mgbe a na-agbanye bọtịnụ ọ bụla, the test software Demo will display the
corresponding key value. Mgbe ị hapụsịrị ya, Isi ihe ngosi bara uru na-apụ n'anya, indicating that
the button upload is normal.

 

9.Nchọpụta ngwa agha

 

10. Mmezi na nlekọta

1. Biko jiri ya na gburugburu na-enwe okpomọkụ na nrụgide dị oke ọkụ na-agbatị
Ndụ Ọrụ;
2. Ejila ihe dị iche iche iji metụ igodo igodo iji gbasaa ndụ nke igodo;
3. Biko debe mpaghara igodo ọcha iji belata uwe igodo;
4. Zere ịkatọ na ịdaba na-emebi emebi na njikwa anya;
5. Ọ bụrụ na ejighi ya ogologo oge, please remove the battery and store the remote control and
battery in a clean and safe place;
6. Pay attention to moisture-proof during storage and transportation.

11.Safety Information

1. Please read the instructions carefully before use. Non-professionals are prohibited
from operating.
2. Please use the original charger or a charger produced by a regular manufacturer with
the same specifications.
3. Please charge in time to avoid incorrect operation due to insufficient power causing
the remote control to be unresponsive.
4. If repair is required, please contact the manufacturer. If the damage is caused by
self-repair, the manufacturer will not provide warranty.