Incazelo
Imodeli Yomkhiqizo
Imodeli: DH12S-LD
Okokusebenza okusebenzayo:crawler wire saw machine
Umdwebo Wezesekeli Yomkhiqizo
Qaphela: Ungakhetha elinye lama-antenna amathathu. I-Antennance ye-Suction Antenna iyindinganiso ngokuzenzakalelayo.
Incazelo yokulawula okukude
Isingeniso Sokubonisa
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (Amapharamitha akwazi ukuguqulwa)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Voltage ephansi: Ibhethri lokulawula kude liphansi kakhulu, Sicela ungene esikhundleni sebhethri.
Inethiwekhi yehle: Isiginali engenantambo iyaphazamiseka. Sicela ubheke amandla owemukelayo, amandla futhi, bese uqala kabusha ukulawula okukude.
Imiyalo yokusebenza yokulawula okukude
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Vula ukushintshwa kwamandla, andthe display will show the motor speed, okubonisa ukuqala okuphumelelayo.
2.Large motor and speed regulation
Jikisa “phambili / emuva” Shintshela phambili, the receiver’s large motor will turn on, and the display will show forward
Jikisa “phambili / emuva” Shintshela emuva, the large motor of the receiver will turn on in reverse, and the display will show reverse
Jikelezisa “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “phambili / emuva” Shintshela phambili, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Jikisa “Phambili / emuva” Shintshela emuva, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Jikisa “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Jikisa “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
Kwimodi yezandla:
Turn left in place: Cindezela ubambe “Enable” button, jikisa “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Cindezela ubambe “Enable” button, jikisa “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” inkinobho futhi ujikeleze “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Ukusika okuzenzakalelayo
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: Kwimodi yezandla, press and hold the “Enable” inkinobho futhi ujikeleze “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 kwa- 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (Abasebenzisi bayenqatshelwe ekuguquleni ngaphandle kwemvume)
Eminye imisebenzi yokulawula okukude ingashintshwa ngamapharamitha. Kwimodi yezandla, when the small motor speed S2 is 10, Cindezela phambili / ukubuyela emuva switch up amahlandla amathathu ngokulandelana, and then push it down three times in a row to enter the parameter menu;
Phuma imenyu yepharamitha: Khetha ukusindisa noma ungagcini, then press the enable button to confirm the exit;
Inani eliphakeme: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, phutha 800, ukuguqulwa akuvunyelwe;
I-Depeleellan Parameter: automatic cutting control parameter. Lapho ukusika kwenani lokushintsha kwamanje kudlula leli nani,deceleration begins.
Ukushesha a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Ukuwohloka A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Ukuhamba Okuphezulu: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Ukushiyeka kwejubane: the maximum speed of the small motor during automatic cutting.
Umsingathi omkhulu: maximum speed of large motor.
Izici zikagesi ezikude
Usayizi wokulawula okukude
Ilungelo lokugcina lokuhumusha lawo mkhiqizo lingelankampani yethu kuphela.
