工業用無線遙控器DH01R-4W-26K

應用:用於各種工業設備

1.最大限度 26 交流 3A/250V 或直流 5A/30V.

2.無障礙傳輸距離為 200 米.

3. 最大限度 4 類比0-10V輸出通道 (顯示範圍可自訂): 支援 2 擴展隔離數位電位器輸出通道;

4. 2 類比輸入; 並顯示在遙控器上, 顯示範圍可自訂.

5. 1 急停繼電器輸出常閉觸點.

低功耗設計
易於使用

MK3-M4

1.產品型號

模型: DH01R-4W-26K

適用設備:各種工業設備

2.產品配件圖

筆記: 您可以選擇三種天線之一. 預設標配吸盤天線.

3.產品型號說明

筆記:
① DH01R系列, 如果後綴包含 T, 表示有急停輸出;不帶T, it means without emergency stop output.

②If there is no analog output, there is no need to remark 0W or 0R; the analogquantities W1, W2, W3, and W4 default to 0-10V analog voltage output; at the same time, W1 and W2 can be expanded to 2 isolated digital potentiometer outputs, with a range of 0 -5K ohms, ½ watt; resolution: 20 ohms. The two digital potentials can be used to control the welding current and welding voltage of the welding machine. If the digital potentiometer output is required, user notes are required.

④Analog input, ranging from 1 to 2, 表示有 1 to 2 類比輸入(最大限度 2 頻道); 當有類比輸入時, 您需要注意類比輸入的電壓範圍 (我們的接收器預設為 0 -5伏, 用戶還可以註釋為 4-20 mA 或 0-10V, 收益) 以及類比量對應的顯示範圍 (例如: 展示 0-100 伏特或 0-1000 安培)

這兩個類比可作為焊接電流和焊接電壓的顯示.

4.特徵

1）Maximum 26 交流 3A/250V 或直流 5A/30V;
2）Maximum 4 類比0-10V輸出通道 (顯示範圍可自訂): 支援 2 擴展隔離數位電位器輸出通道;
3）2 analog inputs; 並顯示在遙控器上, 顯示範圍可自訂
4）1 channels of emergency stop relay output normally closed contacts;
5） Powered by 3 AA電池, low power consumption design;
6） Wireless operation distance is 200 米;
7）Protection grade IP67;
8）With cross switch operation, supports two 4-direction cross switches;
9）Back strap design.

5.遙控開關說明

6.Display content introduction

W1 knob value: W1: 0-1000 (parameter adjustable 0-9999)
W2 knob value: W2: 0-5000 (parameter adjustable 0-9999)
W3 knob value: W3: 0-5000 (parameter adjustable 0-9999)
W4 knob value: W4: 0-5000 (parameter adjustable 0-9999)
ADC1 feedback display: 0-1000 (parameter adjustable 0-5000)
ADC2 feedback display: 0-1000 (parameter adjustable 0-5000)

低電壓: 遙控器電池電量過低, 請更換電池.

網路斷線: 無線訊號中斷. 請檢查接收器功率, 再次打開電源, 並重新啟動遙控器.

7.遙控功能操作說明

1） Turn on the remote control
當接收機開機時, the receiver working indicator flashes; 在遙控器中安裝兩顆 AA 電池, 打開電源開關, and the display shows a value,表示啟動成功. The receiver working indicator light becomes solid.
2）Switch and button functions
Any operation of the twist switch and button on the remote control can control the corresponding switch signal output point on the receiver. All switch signal output points on the receiver are normally open signals by default;
3）W1-W4 speed adjustment
Rotate the knobs in W1-W4 arbitrarily to operate the corresponding analog output signal or potentiometer signal at the receiver end. The analog output signal at the receiver end defaults to a 0-10V voltage signal, and the potentiometer signal defaults to 0-5K;
4） Emergency stop function
When the emergency stop button is pressed, all switch signal outputs are disconnected and the analog output is disconnected; after the emergency stop is released, all switch signals are restored and the analog output is restored; 5 seconds after the remote control is turned off, all switch signal outputs are disconnected and the analog quantities remain unchanged. When the remote control is turned on, the switch signal outputs automatically recover;
5）Parameter menu (users are prohibited from modifying it privately)
Some functions of the remote control can be adjusted through parameters. When the display W1=0, press the K9-B button 3 times in a row, and then press the K9-A button 3 times in a row to enter the parameter menu; K9-A 和 K9-B 鍵用於翻閱選單並選擇參數; 按住K1-A, 然後按K9-A/B按鈕修改參數;
退出參數選單: 選擇儲存或不儲存, 然後按K1-A鍵確認退出;
F1W1範圍: 顯示幕上W1旋鈕的顯示範圍值, 可調自 0 to 9999;
F2W2範圍: W2旋鈕在顯示幕上的顯示範圍值, 可調自 0 to 9999;
F3W3系列: 顯示幕上W3旋鈕的顯示範圍值, 可調自 0 to 9999;
F4W4系列: The display range value of the W4 knob on the display screen, 可調自 0 to 9999
F5A1 range: Display ADC1 feedback display range value, 0-5000 adjustable;
F6A2 range: Display ADC2 feedback display range value, 0-5000 adjustable;
Alarm current: Set the alarm value for ADC1 and ADC2 feedback display. When ADC1 and ADC2 exceed this value, the remote control display will alarm; when this value is 0,the alarm function is invalid;