可編程 CNC 無線遙控器 PHB06B

描述

 

1.產品介紹

The programmable CNC remote control PHB06B is suitable for wireless
各種數控系統嘅遙控運作. It supports users to
customize programming and develop button functions to realize remote
control of various functions on the CNC system; it supports users to
customize programming and develop display content to realize dynamic
display of system status; the remote control comes with a rechargeable
battery and supports Type-C interface charging.

2.產品功能

1. 使用 433MHZ 無線通訊技術, 無線操作
距離係 80 米;
2. 使用自動跳跳功能, 32 無線遙控器
控制器可以同時使用，而唔會影響對方;
3. 支持 12 自訂掣編程;
4. Support 2.8-inch screen, display content custom programming;
5. 支持 1 6-speed axis selection switch, which can be custom programmed;
6. 支持 1 7-speed magnification switch, which can be custom programmed;
7. 支持 1 electronic handwheel, 100 pulses/turn;
8. Support standard Type-C charging; 5V-2A 充電規格; battery
specification 18650/12580mWh battery.

3.工作原則

4. 產品規格

5.產品功能介紹

筆記：
①Power switch：
Control hand wheel to open and close

②Enable buttons on both sides：
The enabling button must be pressed to crank the hand wheel;

③Custom button area
12 buttons arranged in 3X4, 用戶定義嘅編程;

④Axis selection, magnification switch
1 6-position axis selection switch, which can be customized and programmed;
1 7-position ratio switch, which can be customized and programmed

⑤ Emergency stop switch:
Handwheel emergency stop switch;

⑥Display area:
Can display current power, signal, and customized display content;

⑦Electronic hand wheel：
1 electronic handwheel, 100 pulses/turn.

⑧Charging port:

Built-in rechargeable battery, charged using Type-C charger, 充電電壓 5V,
現時 1A-2A; charging time 7 鐘頭;

6.產品配件圖

7.產品安裝指南

1. Insert the USB receiver into the computer, 電腦會自動
recognize and install the USB device driver without manual installation;
2. 將遙控器插入充電器. 電池充滿電後, turn
on the power switch, turn on the remote control, and the display shows normal, which
means the power-on is successful;
3. 開咗之後, 你可以執行任何掣操作. The remote control can
support dual button operation at the same time. 當你按任何掣時, a black
square will appear next to the signal on the remote control, indicating that the button
is valid.

8.產品營運指示
產品開發同使用之前, you can use the Demo software we provide to test
the buttons and display of the remote control, or use the Demo as a reference routine for
future programming development;
喺使用 Demo 軟件之前, 請將 USB 接收器插入電腦, make
sure the remote controller has sufficient power, 開啟電源開關, 然後用佢;
當按遙控器上面嘅任何掣, the test software Demo will display the
corresponding key value. 發佈完之後, 關鍵值顯示消失, indicating that
the button upload is normal.

 

9.產品故障排除

 

10. 維修同照顧

1. 請係乾環境中使用，溫度正常和壓力要延長
使用生活;
2. 唔好用鋒利嘅物件去觸及關鍵區域，延長鎖匙嘅使用壽命;
3. 請保持關鍵區域清潔，以減少關鍵磨損;
4. 避免擠壓同跌落，對遙控器造成損壞;
5. 如果唔用好耐, please remove the battery and store the remote control and
battery in a clean and safe place;
6. 儲存及運輸期間注意防潮.

11.安全資訊

1. 使用前請仔細閱讀指示. Non-professionals are prohibited
from operating.
2. Please use the original charger or a charger produced by a regular manufacturer with
the same specifications.
3. Please charge in time to avoid incorrect operation due to insufficient power causing
the remote control to be unresponsive.
4. 如果需要維修, 請聯絡廠商. If the damage is caused by
self-repair, 廠商唔會提供保養.