Tavsif
Mahsulot modeli
Model: DH12S-LD
Qo'llaniladigan uskunalar:crawler wire saw machine
Mahsulot uchun aksessuarlar diagrammasi
Eslatma: Siz uchta antennalardan birini tanlashingiz mumkin. Assimilyatsiya kubogi antenna sukut bo'yicha standart hisoblanadi.
Masofadan boshqarish pulti Tasvir tavsifi
Discondentni kiritish
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parametrlar sozlanishi)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Kam kuchlanish: Masofadan boshqarish pulti batareyasi juda past, Iltimos batareyani almashtiring.
Tarmoq tushdi: Simsiz signal to'xtatiladi. Iltimos, qabul qilgichning quvvatini tekshiring, uni yana yoqing, va masofadan boshqarish pultini qayta ishga tushiring.
Masofadan boshqarish funktsiyasi operatsiya ko'rsatmalar
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Quvvat tugmachasini yoqing, andthe display will show the motor speed, Muvaffaqiyatli ishga tushirish.
2.Large motor and speed regulation
Turn the “forward/reverse” Oldinga o'tish, the receiver’s large motor will turn on, and the display will show forward
Turn the “forward/reverse” teskari tomonga o'tish, the large motor of the receiver will turn on in reverse, and the display will show reverse
Aylantiring “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “forward/reverse” Oldinga o'tish, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Turn the “Oldinga / teskari” teskari tomonga o'tish, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Turn the “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Turn the “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
In manual mode:
Turn left in place: Press and hold the “Enable” button, burilmoq “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Press and hold the “Enable” button, burilmoq “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” button and rotate the “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Automatic cutting
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In manual mode, press and hold the “Enable” button and rotate the “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 ga 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (users are prohibited from modifying it without permission)
Masofadan boshqarish pultining ba'zi funktsiyalari parametrlar orqali sozlanishi mumkin. In manual mode, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Parametr menyusidan chiqing: Saqlash yoki saqlamaslikni tanlang, then press the enable button to confirm the exit;
Maksimal oqim: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, default 800, modification is prohibited;
Deceleration parameter: automatic cutting control parameter. Kesish oqim o'zgarishi qiymati ushbu qiymatdan oshganda,deceleration begins.
A1 ni tezlashtirish: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
A2 ni sekinlashtirish: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maksimal yurish: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Tezlik chegarasi ofset: the maximum speed of the small motor during automatic cutting.
Maksimal xost: maximum speed of large motor.
Remote control electrical characteristics
Remote control size
The final interpretation right of this product belongs only to our company.
