Açıklama
1.Product model
Modeli: DH01R-4W-26K
Applicable equipment:various industrial equipment
2.Product accessories diagram
Not: You can choose one of the three antennas. The suction cup antenna is standard by default.
3.Product model description
Not:
① DH01R series, if the suffix contains T, it means with emergency stop output;without T, acil durdurma çıkışının olmadığı anlamına gelir.
②Analog çıkış yoksa, 0W veya 0R'yi belirtmeye gerek yok; analog miktarlar W1, W2, W3, ve W4 varsayılanı 0-10V analog voltaj çıkışıdır; aynı zamanda, W1 ve W2 genişletilebilir 2 izole dijital potansiyometre çıkışları, bir dizi 0 -5K ohm, ½ watt; çözünürlük: 20 ohm. Kaynak makinesinin kaynak akımını ve kaynak voltajını kontrol etmek için iki dijital potansiyel kullanılabilir. Dijital potansiyometre çıkışı gerekiyorsa, kullanıcı notları gerekli.
④Analog giriş, arasında değişen 1 ile 2, bulunduğunu belirten 1 ile 2 analog girişler(maksimum 2 kanallar); analog giriş olduğunda, analog girişin voltaj aralığına dikkat etmeniz gerekir (alıcımız varsayılan olarak 0 -5V, kullanıcı ayrıca şunu da not edebilir: 4-20 mA veya 0-10V, vb.) ve analog miktarın karşılık gelen görüntüleme aralığı (Örneğin: görüntülemek 0-100 volt veya 0-1000 amper)
Bu iki analog miktar, kaynak akımı ve kaynak gerilimi için gösterge olarak kullanılabilir.
4.Özellikleri
1）Maximum 26 Kaynak makinesi otomasyonu kaynak ve kaynak operatörü. Döner Rulolar 1. Frekans atlamalı iletim teknolojisini kullanma;
2）Maximum 4 analog 0-10V çıkış kanalları (ekran aralığı özelleştirilebilir): destekler 2 genişletilmiş izole dijital potansiyometre çıkışı kanalları;
3）2 analog inputs; ve uzaktan kumandada görüntülenir, ekran aralığı özelleştirilebilir
4）1 channels of emergency stop relay output normally closed contacts;
5） Powered by 3 AA piller, low power consumption design;
6） Wireless operation distance is 200 metre;
7）Protection grade IP67;
8）With cross switch operation, supports two 4-direction cross switches;
9）Back strap design.
5.Remote control switch description
6.Display content introduction
W1 knob value: W1: 0-1000 (parameter adjustable 0-9999)
W2 knob value: W2: 0-5000 (parameter adjustable 0-9999)
W3 knob value: W3: 0-5000 (parameter adjustable 0-9999)
W4 knob value: W4: 0-5000 (parameter adjustable 0-9999)
ADC1 feedback display: 0-1000 (parameter adjustable 0-5000)
ADC2 feedback display: 0-1000 (parameter adjustable 0-5000)
Low voltage: The remote control battery is too low, please replace the battery.
Network dropped: The wireless signal is interrupted. Please check the power of the receiver, power it on again, and restart the remote control.
7.Remote control function operation instructions
1） Turn on the remote control
When the receiver is powered on, the receiver working indicator flashes; install two AA batteries in the remote control, turn on the power switch, and the display shows a value,indicating successful startup. The receiver working indicator light becomes solid.
2）Switch and button functions
Any operation of the twist switch and button on the remote control can control the corresponding switch signal output point on the receiver. All switch signal output points on the receiver are normally open signals by default;
3）W1-W4 speed adjustment
Rotate the knobs in W1-W4 arbitrarily to operate the corresponding analog output signal or potentiometer signal at the receiver end. The analog output signal at the receiver end defaults to a 0-10V voltage signal, and the potentiometer signal defaults to 0-5K;
4） Emergency stop function
When the emergency stop button is pressed, all switch signal outputs are disconnected and the analog output is disconnected; after the emergency stop is released, all switch signals are restored and the analog output is restored; 5 seconds after the remote control is turned off, all switch signal outputs are disconnected and the analog quantities remain unchanged. When the remote control is turned on, the switch signal outputs automatically recover;
5）Parameter menu (users are prohibited from modifying it privately)
Some functions of the remote control can be adjusted through parameters. When the display W1=0, press the K9-B button 3 times in a row, and then press the K9-A button 3 times in a row to enter the parameter menu; K9-A and K9-B key to page through the menu and select parameters; hold down K1-A, and then press the K9-A/B button to modify parameters;
Exit the parameter menu: choose to save or not save, and then press the K1-A button to confirm the exit;
F1W1 range: The display range value of the W1 knob on the display screen, adjustable from 0 ile 9999;
F2W2 range: The display range value of the W2 knob on the display screen, adjustable from 0 ile 9999;
F3W3 range: The display range value of the W3 knob on the display screen, adjustable from 0 ile 9999;
F4W4 range: The display range value of the W4 knob on the display screen, adjustable from 0 ile 9999
F5A1 range: Display ADC1 feedback display range value, 0-5000 adjustable;
F6A2 range: Display ADC2 feedback display range value, 0-5000 adjustable;
Alarm current: Set the alarm value for ADC1 and ADC2 feedback display. When ADC1 and ADC2 exceed this value, the remote control display will alarm; when this value is 0,the alarm function is invalid;
8.Remote control electrical characteristics
9.Remote control size
The final interpretation right of this product belongs only to our company.
