Uygulama:Paletli tel testere makinesi için özel olarak kullanılır
1.Otomatik kesme modunu destekler, Küçük motorun yürüme hızını büyük motor akımına göre otomatik olarak ayarlar, ve otomatik kesme kontrolü sağlar.
2.Engelsiz iletim mesafesi 200 metre.
3. Büyük motorlar ve küçük motorlar için çift hız regülasyonunu destekler.
4. Küçük motorun yerinde dönmesini destekleyin.
5. Sol ve sağ tekerlek küçük motorlu doğrusal düzeltmeyi destekler.
Modeli: DH12S-LD
Uygulanabilir ekipman:crawler wire saw machine
Not: Üç antenden birini seçebilirsiniz. Vantuz anteni varsayılan olarak standarttır.
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parametreler ayarlanabilir)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Düşük voltaj: Uzaktan kumandanın pili çok düşük, lütfen pili değiştirin.
Ağ kesildi: Kablosuz sinyal kesildi. Lütfen alıcının gücünü kontrol edin, tekrar aç, ve uzaktan kumandayı yeniden başlatın.
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, güç anahtarını aç, andthe display will show the motor speed, Başarılı başlatmayı gösteren.
2.Large motor and speed regulation
Çevir “ileri/geri” ileriye doğru geçiş yap, the receiver’s large motor will turn on, and the display will show forward
Çevir “ileri/geri” geri vitese geç, the large motor of the receiver will turn on in reverse, and the display will show reverse
Döndür “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “ileri/geri” ileriye doğru geçiş yap, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Çevir “İleri/Geri” geri vitese geç, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Çevir “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Çevir “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
Manuel modda:
Turn left in place: tuşunu basılı tutun “Enable” button, çevir “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: tuşunu basılı tutun “Enable” button, çevir “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” düğmesine basın ve döndürün “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Otomatik kesme
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: Manuel modda, press and hold the “Enable” düğmesine basın ve döndürün “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 ile 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (kullanıcıların izinsiz olarak değişiklik yapması yasaktır)
Some functions of the remote control can be adjusted through parameters. Manuel modda, when the small motor speed S2 is 10, ileri/geri düğmesini art arda üç kez yukarı itin, and then push it down three times in a row to enter the parameter menu;
Parametre menüsünden çıkış: choose to save or not save, then press the enable button to confirm the exit;
Maksimum akım: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, varsayılan 800, değişiklik yasaktır;
Yavaşlama parametresi: automatic cutting control parameter. Kesme akımı değişim değeri bu değeri aştığında,deceleration begins.
Hızlanma a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Yavaşlama a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maksimum yürüyüş: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Hız limiti ofseti: the maximum speed of the small motor during automatic cutting.
Maksimum ana bilgisayar: maximum speed of large motor.
Bu ürünün son yorumlama hakkı sadece firmamıza aittir..
