Paglalarawan
Modelo ng produkto
Modelo: DH12S-LD
Naaangkop na kagamitan:crawler wire saw machine
Diagram ng mga accessory ng produkto
Tandaan: Maaari kang pumili ng isa sa tatlong mga antenna. Ang antena ng suction cup ay pamantayan sa pamamagitan ng default.
Paglalarawan ng Remote Control Switch
Displaycontent introduction
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Mababang boltahe: Ang baterya ng remote control ay masyadong mababa, Mangyaring palitan ang baterya.
Bumagsak ang network: Ang wireless signal ay nagambala. Mangyaring suriin ang lakas ng tatanggap, i -kapangyarihan ito muli, at i -restart ang remote control.
Mga tagubilin sa operasyon ng Remote Control Function
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, I -on ang switch ng kuryente, andthe display will show the motor speed, nagpapahiwatig ng matagumpay na pagsisimula.
2.Large motor and speed regulation
Turn the “forward/reverse” switch to forward, the receiver’s large motor will turn on, and the display will show forward
Turn the “forward/reverse” switch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse
Rotate the “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “forward/reverse” switch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Turn the “Forward/Reverse” switch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Turn the “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Turn the “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
In manual mode:
Turn left in place: Press and hold the “Enable” pindutan, turn the “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Press and hold the “Enable” pindutan, turn the “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” button and rotate the “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Automatic cutting
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In manual mode, press and hold the “Enable” button and rotate the “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 sa 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (users are prohibited from modifying it without permission)
Ang ilang mga pag -andar ng remote control ay maaaring maiakma sa pamamagitan ng mga parameter. In manual mode, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Lumabas sa menu ng parameter: Piliin upang makatipid o hindi makatipid, then press the enable button to confirm the exit;
Maximum current: the operating rated current of the cutting motor is 80% ng kasalukuyang ito;
Mga parameter ng control ng bilis: Awtomatikong mga parameter ng control control, default 800, Ipinagbabawal ang pagbabago;
Parameter ng Deceleration: Awtomatikong parameter ng control control. Kapag ang pagputol ng kasalukuyang halaga ng pagbabago ay lumampas sa halagang ito,Nagsisimula ang pagkabulok.
Acceleration A1: Awtomatikong parameter ng control control, Kapag ang pagputol kasalukuyang ay mas mababa kaysa sa itinakdang kasalukuyang pagputol, Ang bilis ng pagpabilis;
Deceleration A2: Awtomatikong parameter ng control control, Kapag ang kasalukuyang pagputol ay mas mataas kaysa sa set
pagputol ng kasalukuyang, Ang bilis ng pagkabulok;
Awtomatikong pag -urong ng kutsilyo: hindi wasto;
Simulan ang pag-lock sa sarili: 0, Walang pag-lock sa sarili; 1, Pag-lock sa sarili. Pindutin ang Paganahin Key + Ipasa at baligtad upang maganap at mag-lock sa sarili.
Pinakamataas na paglalakad: Ang maximum na bilis ng maliit na motor.
Pagputol ng kasalukuyang: Itakda ang maximum na kasalukuyang ng pangunahing motor para sa awtomatikong paggupit. Kung ang kasalukuyang feedback ay lumampas sa halagang ito, Magsisimula itong mabulok.
Default na limitasyon ng bilis: Ang default na maximum na bilis ng awtomatikong bilis ng pagputol kapag naka -on sa makina.
Awtomatikong mode: 0, Ang awtomatikong switch ay awtomatikong kinokontrol; 1, Kinokontrol ng awtomatikong switch ang awtomatikong punto ng output ng IO.
Bilis ng limitasyon ng bilis: Ang maximum na bilis ng maliit na motor sa panahon ng awtomatikong paggupit.
Pinakamataas na host: Pinakamataas na bilis ng malaking motor.
Remote control na mga katangian ng elektrikal
Laki ng Remote Control
Ang pangwakas na interpretasyon na karapatan ng produktong ito ay kabilang lamang sa aming kumpanya.
