Ansökan:Speciellt används för Crawler Wire Saw Machine
1.Stöder automatiskt skärningsläge, justerar automatiskt den lilla motorns gånghastighet enligt den stora motorströmmen, och uppnår automatisk skärkontroll.
2.Barriärfritt överföringsavstånd är 200 meter.
3. Stöder reglering av dubbla hastigheter för stora motorer och små motorer.
4. Stödja liten motor som svänger på plats.
5. Stöder vänster och höger hjul liten motorisk linjär korrigering.
Modell: DH12S-LD
Tillämplig utrustning:Crawler Wire Saw Machine
Notera: Du kan välja en av de tre antennerna. Sugskoppantennen är som standard standard.
Stor motorisk hastighet：S1：0-50
Liten motorisk hastighet: S2: 0-50
MaximalspeedlimitofAutomatic CuttingSmallMotor:F:0-30(parameters justerbar)
Automatisk skärning av maximal ström: Ic: 0-35 (parametrar justerbara)
Linjär korrigeringsvärde: Df: -99-99 (1 unit is about 0.02V)
Lågspänning: Fjärrkontrollbatteriet är för lågt, Byt ut batteriet.
Nätverk tappat: Den trådlösa signalen avbryts. Kontrollera mottagarens kraft, Slå på det igen, och starta om fjärrkontrollen.
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Slå på strömbrytaren, andthe display will show the motor speed, indikerar framgångsrik start.
2.Large motor and speed regulation
Vrid “framåt/bakåt” switch to forward, the receiver’s large motor will turn on, and the display will show forward
Vrid “framåt/bakåt” switch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse
Rotera “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “framåt/bakåt” switch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Vrid “Forward/Reverse” switch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Vrid “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Vrid “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
I manuellt läge:
Turn left in place: Tryck och håll i “Enable” button, turn the “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Tryck och håll i “Enable” button, turn the “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” knappen och rotera “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Automatic cutting
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: I manuellt läge, press and hold the “Enable” knappen och rotera “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 till 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (Användare är förbjudna att ändra det utan tillstånd)
Vissa funktioner i fjärrkontrollen kan justeras via parametrar. I manuellt läge, when the small motor speed S2 is 10, Tryck framåt/omvänd switch upp tre gånger i rad, and then push it down three times in a row to enter the parameter menu;
Avsluta parametermenyn: Välj att spara eller inte spara, then press the enable button to confirm the exit;
Maximum current: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, standard 800, modifiering är förbjuden;
Retardationsparameter: automatic cutting control parameter. När det skärande strömförändringsvärdet överstiger detta värde,deceleration begins.
Acceleration A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Retardation A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximum walking: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Speed limit offset: the maximum speed of the small motor during automatic cutting.
Maximum host: maximum speed of large motor.
Den slutliga tolkningsrätten för denna produkt tillhör bara vårt företag.
