Tlhaloso
Mohlala oa sehlahisoa
Mohlala: DH12S-LD
Lisebelisoa tse sebetsang:crawler wire saw machine
Setšoantšo sa thepa ea sehlahisoa
Hlokomela: O ka khetha e 'ngoe ea li-antenas tse tharo. The Spoction Cup Anutennah ke molao-moea o sa feleng.
Tlhaloso ea setsi sa taolo ea sebaka se hole
Kenyelletso ea bonfong
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (Liraro tsa parameter)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Lijo tse tlase tsa voltage: Better ea taolo e hole haholo e tlase haholo, ka kopo fetola betri.
Marang-rang a oa: Lets'oao le se nang mohala le sitisoa. Ka kopo sheba matla a moamoheli, e e matla hape, 'me u qale mosebetsi o haufi.
Litaelo tsa Ts'ebetso ea Ts'ebetso ea Ts'ebetso ea Ts'ebetso
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Bulela phetoho ea motlakase, andthe display will show the motor speed, Ho bontša ho qala ka katleho.
2.Large motor and speed regulation
Bulela “Pele / Reverse” Fetolela ho ea pele, the receiver’s large motor will turn on, and the display will show forward
Bulela “Pele / Reverse” Fetolela ho khutlisa, the large motor of the receiver will turn on in reverse, and the display will show reverse
Potoloha “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “Pele / Reverse” Fetolela ho ea pele, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Bulela “Pele / Reverse” Fetolela ho khutlisa, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Bulela “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Bulela “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
Ka mokhoa oa bukana:
Turn left in place: Tobetsa le ho ts'oara “Enable” button, bulela “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Tobetsa le ho ts'oara “Enable” button, bulela “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” konopo ebe o potoloha “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Ho seha ka ho iketsa
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: Ka mokhoa oa bukana, press and hold the “Enable” konopo ebe o potoloha “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 to 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (Basebelisi ba thibetsoe ho fetoloa ntle le tumello)
Some functions of the remote control can be adjusted through parameters. Ka mokhoa oa bukana, when the small motor speed S2 is 10, sutumelletsa pele / e khutlisetsang makhetlo a mararo ka tatellano, and then push it down three times in a row to enter the parameter menu;
Tlosa ho menu ea parameter: khetha ho boloka kapa ho se boloke, then press the enable button to confirm the exit;
Boholo ba hona joale: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, kamehla 800, Phetoho e thibetsoe;
Paramente ea thetso: automatic cutting control parameter. Ha boleng ba phetoho ea hona joale bo feta boleng bona,deceleration begins.
Potlakisa a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Thetso A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Ho tsamaea haholo: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Meeli ea lebelo le tima: the maximum speed of the small motor during automatic cutting.
Moamoheli ea phahameng: maximum speed of large motor.
Litšobotsi tse hole tsa motlakase
Boholo ba taolo ea taolo
Tlhaloso ea ho qetela ea sehlahisoa sena ke feela ho k'hamphani ea rona.
