Fa'amatalaga
1.Fa'ata'ita'iga o oloa
Fa'ata'ita'iga: DH01R-4W-26K
Meafaigaluega talafeagai:meafaigaluega tau alamanuia eseese
2.Ata fa'aoga oloa
Manatua: E mafai ona e filifilia se tasi o antenna e tolu. O le antenna ipu suction e masani ona le mafai.
3.Fa'amatalaga fa'atusa o oloa
Manatua:
① DH01R faasologa, pe afai o le suffix e iai le T, o lona uiga fa'atasi ma fa'alavelave fa'afuase'i fa'agata fa'alavelave;e aunoa ma le T, o lona uiga e aunoa ma se fa'alavelave fa'afuase'i fa'agata fa'alavelave.
②Afai e leai se gaioiga fa'atusa, e leai se mana'oga e fa'ailoa le 0W po'o le 0R; mea tutusa W1, W2, W3, ma le W4 fa'aletonu i le 0-10V analog voltage gaosiga; i le taim lava lena, W1 ma W2 e mafai ona faʻalauteleina i 2 tu'ufua fa'afuainumera potentiometer, ma le tele o 0 -5K ohms, ½ watt; iugafono: 20 ohms. E mafai ona faʻaogaina le lua numera numera e pulea ai le faʻaogaina o le taimi nei ma le uʻamea voltage o le masini uʻamea. Afai e mana'omia le gaosiga o le potentiometer numera, e mana'omia ni fa'amatalaga a le tagata fa'aoga.
④Analog input, amata mai 1 ia 2, e faailoa mai ai e iai 1 ia 2 mea fa'aoga analog(maualuga 2 alavai); pe a iai se fa'aoga analog, e tatau ona e maitauina le laina eletise o le faʻaoga analog (ua faaletonu le tatou tagata e taliaina 0 -5Uafu Ethernet, e mafai foi e le tagata faʻaoga ona matauina e pei o 4-20 mA poʻo le 0-10V, ma isi.) ma le fa'aaliga fa'atusa tutusa o le aofa'i fa'atusa (faataitaiga: fa'aaliga 0-100 volts po o 0-1000 amp)
E mafai ona fa'aogaina nei aofa'iga fa'atusa e lua e fai ma fa'aaliga mo le u'iina o le taimi nei ma le u'u eletise.
4.Features
1）Maximum 26 Uumea masini otometi uelo ma uelo operator. Liliu Rolls 1. Fa'aaogaina fa'atekonolosi fe'avea'i fa'avave;
2）Maximum 4 ala o analog 0-10V galuega faatino (fa'aaliga avanoa e mafai ona fa'apitoa): lagolago 2 ala o fa'alautele fa'afuafua fa'afuainumera potentiometer;
3）2 analog inputs; ma fa'aalia i luga o le fa'atonu mamao, e mafai ona fa'apitoa le fa'aaliga fa'aaliga
4）1 channels of emergency stop relay output normally closed contacts;
5） Powered by 3 AA maa, mamanu faʻaaogaina eletise maualalo;
6） Wireless operation distance is 200 mita;
7）Protection grade IP67;
8）With cross switch operation, lagolago lua 4-itu kolose ki;
9）Back strap design.
5.Fa'amatalaga ki fa'atonu mamao
6.Fa'aali atu le folasaga o anotusi
W1 kip tau: W1: 0-1000 (fetuutuunai parakalafa 0-9999)
W2 knob value: W2: 0-5000 (fetuutuunai parakalafa 0-9999)
W3 knob value: W3: 0-5000 (fetuutuunai parakalafa 0-9999)
W4 knob value: W4: 0-5000 (fetuutuunai parakalafa 0-9999)
ADC1 feedback display: 0-1000 (fetuutuunai parakalafa 0-5000)
ADC2 feedback display: 0-1000 (fetuutuunai parakalafa 0-5000)
Low voltage: The remote control battery is too low, please replace the battery.
Network dropped: The wireless signal is interrupted. Please check the power of the receiver, power it on again, and restart the remote control.
7.Remote control function operation instructions
1） Turn on the remote control
When the receiver is powered on, the receiver working indicator flashes; install two AA batteries in the remote control, turn on the power switch, and the display shows a value,indicating successful startup. The receiver working indicator light becomes solid.
2）Switch and button functions
Any operation of the twist switch and button on the remote control can control the corresponding switch signal output point on the receiver. All switch signal output points on the receiver are normally open signals by default;
3）W1-W4 speed adjustment
Rotate the knobs in W1-W4 arbitrarily to operate the corresponding analog output signal or potentiometer signal at the receiver end. The analog output signal at the receiver end defaults to a 0-10V voltage signal, and the potentiometer signal defaults to 0-5K;
4） Emergency stop function
When the emergency stop button is pressed, all switch signal outputs are disconnected and the analog output is disconnected; after the emergency stop is released, all switch signals are restored and the analog output is restored; 5 seconds after the remote control is turned off, all switch signal outputs are disconnected and the analog quantities remain unchanged. When the remote control is turned on, the switch signal outputs automatically recover;
5）Parameter menu (users are prohibited from modifying it privately)
Some functions of the remote control can be adjusted through parameters. When the display W1=0, press the K9-B button 3 times in a row, and then press the K9-A button 3 times in a row to enter the parameter menu; K9-A ma K9-B ki i le itulau e ala i le lisi ma filifili tapulaʻa; taofi i lalo K1-A, ona oomi lea o le K9-A/B fa'amau e sui fa'amau;
Tu'u ese mai le lisi o fa'asologa: filifili e teu pe leai, ona oomi lea o le K1-A faamau e faʻamaonia ai le alu ese;
F1W1 va'aiga: Le tau fa'aaliga fa'aaliga o le kipo W1 i luga o le fa'aaliga fa'aaliga, fetuutuunai mai 0 ia 9999;
F2W2 va'aiga: Le tau fa'aaliga fa'aaliga o le kipo W2 i luga o le fa'aaliga fa'aaliga, fetuutuunai mai 0 ia 9999;
F3W3 va'aiga: Le tau fa'aaliga va'aiga o le kipo W3 i luga o le fa'aaliga fa'aaliga, fetuutuunai mai 0 ia 9999;
F4W4 va'aiga: The display range value of the W4 knob on the display screen, fetuutuunai mai 0 ia 9999
F5A1 range: Display ADC1 feedback display range value, 0-5000 adjustable;
F6A2 range: Display ADC2 feedback display range value, 0-5000 adjustable;
Alarm current: Set the alarm value for ADC1 and ADC2 feedback display. When ADC1 and ADC2 exceed this value, the remote control display will alarm; when this value is 0,the alarm function is invalid;
8.Remote control electrical characteristics
9.Remote control size
The final interpretation right of this product belongs only to our company.
