Na vaʻaia e le uaea o le paʻu masini

Faʻamatalaga

Motion faataitaiga

Faʻataʻitaʻiga: DH12S-LD

Masini talafeagai:crawler wire saw machine

Oloa oloa

Tusi: E mafai ona e filifilia se tasi o le tolu antennas. O le faʻamatalaga o le ipu antena o le tapulaʻa e ala i le masani ai.

O le Repram Reply Tralin Faamatalaga

FAʻAALIGA FAʻAFITAULI

Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (Paramests fetuunai)
Linear correction value: O: -99-99 (1 unit is about 0.02V)

Maualalo voltage: O le mea e sili ona maualalo ai le paʻu, Faʻamolemole sui le maʻa.

Taavale na pauu: O le uaealesi e le mafai ona motusia. Faʻamolemole siaki le malosi o le tagata e suʻe, mana e toe i ai, ma toe amata le mea mamao.

Fofoga o le Repree Production Action Prociction faatonuga

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Liliu le mana eletise, andthe display will show the motor speed, Faasino le manuia amata.

2.Large motor and speed regulation

Liliu le “Luma / Suiga” Alu i luma, the receiver’s large motor will turn on, and the display will show forward

Liliu le “Luma / Suiga” Suia i le fesuiaiga, the large motor of the receiver will turn on in reverse, and the display will show reverse

Liliuina le “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move the “Luma / Suiga” Alu i luma, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Liliu le “Luma / Suiga” Suia i le fesuiaiga, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Liliu le “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Liliu le “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

I le tusi lesona:
Turn left in place: Fetaomi ma taofi le “Enable” button, liliu le “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Fetaomi ma taofi le “Enable” button, liliu le “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

I le otometi faiga: press and hold the “Enable” faamau ma liligi le “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;

7.Otometi tipi

The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: I le tusi lesona, press and hold the “Enable” faamau ma liligi le “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 i 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (Tagata faʻaaoga e faʻasaina mai le suia i totonu e aunoa ma se faʻatagaina)

Some functions of the remote control can be adjusted through parameters. I le tusi lesona, when the small motor speed S2 is 10, Toso le luma / toe suia le ki i le tolu taimi i le laina, and then push it down three times in a row to enter the parameter menu;
Alu i fafo le tapulaa menu: choose to save or not save, then press the enable button to confirm the exit;
Maualuga o taimi nei: the operating rated current of the cutting motor is 80% of this currentt;
Saoasaoa pule: automatic cutting control parameters, lē oʻo mai 800, E faasa;
Faasee faalemafaufau: automatic cutting control parameter. O le taimi o le tipiina o le suiga o le taimi nei e sili atu le taua,deceleration begins.
Saoasaoa a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Faasee a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Amata le tagata lava ia: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Sili atu le savali: the maximum speed of the small motor.
Tipi nei: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Tapulaa le saoasaoa tapulaa: the default maximum speed of automatic cutting speed when turning on the machine.
Otometi faiga: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Tauvaga saoasaoa: the maximum speed of the small motor during automatic cutting.
Sili Atu Maualuga: maximum speed of large motor.

O LE FOLIGA O LE TOE TULAGA OLINGINGING

Tatala le saoasaoa

O le faʻamatalaga mulimuli o lenei oloa e naʻo le matou kamupani.