Программируемый беспроводной пульт дистанционного управления с ЧПУ PHB06B

Описание

 

1.Product Introduction

The programmable CNC remote control PHB06B is suitable for wireless
remote control operation of various CNC systems. It supports users to
customize programming and develop button functions to realize remote
control of various functions on the CNC system; it supports users to
customize programming and develop display content to realize dynamic
display of system status; the remote control comes with a rechargeable
battery and supports Type-C interface charging.

2.Особенности продукта

1. Using 433MHZ wireless communication technology, the wireless operation
distance is 80 метры;
2. Using automatic frequency hopping function, 32 sets of wireless remote
controllers can be used at the same time without affecting each other;
3. Служба поддержки 12 custom button programming;
4. Support 2.8-inch screen, display content custom programming;
5. Служба поддержки 1 6-speed axis selection switch, which can be custom programmed;
6. Служба поддержки 1 7-speed magnification switch, which can be custom programmed;
7. Служба поддержки 1 электронный маховик, 100 pulses/turn;
8. Support standard Type-C charging; 5V-2A charging specification; battery
specification 18650/12580mWh battery.

3.операция более удобна

4. Product specifications

5.Product function introduction

Notes：
①Power switch：
Control hand wheel to open and close

②Enable buttons on both sides：
The enabling button must be pressed to crank the hand wheel;

③Custom button area
12 buttons arranged in 3X4, user-defined programming;

④Axis selection, magnification switch
1 6-position axis selection switch, which can be customized and programmed;
1 7-position ratio switch, which can be customized and programmed

⑤ Emergency stop switch:
Handwheel emergency stop switch;

⑥Display area:
Can display current power, signal, and customized display content;

⑦Electronic hand wheel：
1 электронный маховик, 100 pulses/turn.

⑧Charging port:

Built-in rechargeable battery, charged using Type-C charger, charging voltage 5V,
current 1A-2A; charging time 7 часы;

6.Схема аксессуаров продукта

7.Product Installation Guide

1. Insert the USB receiver into the computer, the computer will automatically
recognize and install the USB device driver without manual installation;
2. Insert the remote control into the charger. After the battery is fully charged, turn
on the power switch, turn on the remote control, and the display shows normal, which
means the power-on is successful;
3. After powering on, you can perform any button operation. The remote control can
support dual button operation at the same time. When you press any button, a black
square will appear next to the signal on the remote control, indicating that the button
is valid.

8.Product Operation Instructions
Before product development and use, you can use the Demo software we provide to test
the buttons and display of the remote control, or use the Demo as a reference routine for
future programming development;
Before using the Demo software, please plug the USB receiver into the computer, make
sure the remote controller has sufficient power, включите выключатель питания, and then use it;
When any button on the remote control is pressed, the test software Demo will display the
corresponding key value. After releasing it, the key value display disappears, indicating that
the button upload is normal.

 

9.Product Troubleshooting

 

10. Maintenance and care

1. Please use it in a dry environment with normal temperature and pressure to extend
the service life;
2. Do not use sharp objects to touch the key area to extend the service life of the key;
3. Please keep the key area clean to reduce key wear;
4. Avoid squeezing and falling to cause damage to the remote control;
5. If not used for a long time, please remove the battery and store the remote control and
battery in a clean and safe place;
6. Pay attention to moisture-proof during storage and transportation.

11.Safety Information

1. Please read the instructions carefully before use. Non-professionals are prohibited
from operating.
2. Please use the original charger or a charger produced by a regular manufacturer with
the same specifications.
3. Please charge in time to avoid incorrect operation due to insufficient power causing
the remote control to be unresponsive.
4. If repair is required, please contact the manufacturer. If the damage is caused by
self-repair, the manufacturer will not provide warranty.