Opis
1.Model produktu
Model: DH12S-P6S
Obowiązujący sprzęt:wire saw/blade saw machine
2.Schemat akcesoriów produktu
Notatka: Możesz wybrać jedną z trzech anten. Antena z przyssawką jest standardem w standardzie.
3.Opis przełącznika zdalnego sterowania
4.Wprowadzenie do treści displayowych
Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(parametry regulowane)
Automatic cutting main motor setting current: Setting: 28 (parametry regulowane)
Swing arm motor speed: Swing: 0-50
Niskie napięcie: Bateria pilota jest zbyt słaba, proszę wymienić baterię.
Sieć upadła: Sygnał bezprzewodowy został przerwany. Proszę sprawdzić moc odbiornika, włącz go ponownie, i uruchom ponownie pilota.
5.Instrukcja obsługi funkcji zdalnego sterowania
1）Turn on the remote control
Gdy odbiornik jest włączony, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; włóż do pilota dwie baterie AA, włącz wyłącznik zasilania, and the display will show the motor speed, wskazując pomyślne uruchomienie.
2）Large motor and speed regulation/Main motor and speed regulation
Press and hold “Speed Regulation Enable”, obróć “Do przodu/do tyłu” przełącz do przodu, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, obróć “Do przodu/do tyłu” przełączyć na bieg wsteczny, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Obróć “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;
3）Traveling motor
Press and hold “Speed Adjustment Enable”, obróć “Do przodu/do tyłu” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
Obróć “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
Naciśnij i przytrzymaj “speed adjustment enable” przycisk i obróć “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “do przodu/do tyłu” switch forward or backward to enter the automatic cutting mode;
7） Parameter menu (użytkownikom nie wolno modyfikować ich bez pozwolenia)
Enter the parameter menu:W trybie ręcznym, when the main motor speed is 0, naciśnij przełącznik do przodu/do tyłu trzy razy z rzędu, and then push it down three times in a row to enterthe parameter menu;
Wyjdź z menu parametrów: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, domyślny 800, unit milli second,modyfikacja jest zabroniona;
Parametr opóźnienia: Gdy wartość zmiany prądu cięcia przekracza tę wartość, rapid deceleration begins, unit Ampere;
Przyspieszenie a1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Zwolnienie a2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, modyfikacja jest zabroniona;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, modyfikacja jest zabroniona;
Maksymalny prąd: The range of main motor feedback current, unit Ampere;
Maksymalny gospodarz: Remote control main motor speed adjustment display range;
Maksymalne chodzenie: Invalid parameter;
Przesunięcie ograniczenia prędkości: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Automatyczne cięcie, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
6.Charakterystyka elektryczna pilota zdalnego sterowania
7.Rozmiar pilota
Ostateczne prawo do interpretacji tego produktu należy wyłącznie do naszej firmy.
