Programmerbar CNC trådløs fjernkontroll PHB06B

Beskrivelse

 

1.Product Introduction

The programmable CNC remote control PHB06B is suitable for wireless
remote control operation of various CNC systems. It supports users to
customize programming and develop button functions to realize remote
control of various functions on the CNC system; it supports users to
customize programming and develop display content to realize dynamic
display of system status; the remote control comes with a rechargeable
battery and supports Type-C interface charging.

2.Produktfunksjoner

1. Using 433MHZ wireless communication technology, the wireless operation
distance is 80 meter;
2. Using automatic frequency hopping function, 32 sets of wireless remote
controllers can be used at the same time without affecting each other;
3. Brukerstøtte 12 custom button programming;
4. Support 2.8-inch screen, display content custom programming;
5. Brukerstøtte 1 6-speed axis selection switch, which can be custom programmed;
6. Brukerstøtte 1 7-speed magnification switch, which can be custom programmed;
7. Brukerstøtte 1 elektronisk håndhjul, 100 pulses/turn;
8. Support standard Type-C charging; 5V-2A ladespesifikasjon; battery
specification 18650/12580mWh battery.

3.kabelfeilfrekvensen reduseres

4. Produktspesifikasjoner

5.Produktfunksjon introduksjon

Notater：
①Power switch：
Control hand wheel to open and close

②Enable buttons on both sides：
The enabling button must be pressed to crank the hand wheel;

③Custom button area
12 buttons arranged in 3X4, brukerdefinert programmering;

④Axis selection, magnification switch
1 6-position axis selection switch, which can be customized and programmed;
1 7-position ratio switch, which can be customized and programmed

⑤ Emergency stop switch:
Handwheel emergency stop switch;

⑥Display area:
Can display current power, signal, and customized display content;

⑦Electronic hand wheel：
1 elektronisk håndhjul, 100 pulses/turn.

⑧Charging port:

Built-in rechargeable battery, charged using Type-C charger, ladespenning 5V,
strøm 1A-2A; charging time 7 timer;

6.Produkttilbehør diagram

7.Produktinstallasjonsveiledning

1. Insert the USB receiver into the computer, datamaskinen vil automatisk
recognize and install the USB device driver without manual installation;
2. Sett fjernkontrollen inn i laderen. Etter at batteriet er fulladet, turn
on the power switch, turn on the remote control, and the display shows normal, which
means the power-on is successful;
3. After powering on, you can perform any button operation. The remote control can
support dual button operation at the same time. When you press any button, a black
square will appear next to the signal on the remote control, indicating that the button
is valid.

8.Product Operation Instructions
Before product development and use, you can use the Demo software we provide to test
the buttons and display of the remote control, or use the Demo as a reference routine for
future programming development;
Before using the Demo software, please plug the USB receiver into the computer, make
sure the remote controller has sufficient power, slå på strømbryteren, and then use it;
When any button on the remote control is pressed, the test software Demo will display the
corresponding key value. Etter å ha sluppet den, nøkkelverdivisningen forsvinner, indicating that
the button upload is normal.

 

9.Feilsøking av produktet

 

10. Vedlikehold og stell

1. Bruk den i et tørt miljø med normal temperatur og trykk for å forlenge
levetiden;
2. Ikke bruk skarpe gjenstander til å berøre nøkkelområdet for å forlenge levetiden til nøkkelen;
3. Hold nøkkelområdet rent for å redusere nøkkelslitasje;
4. Unngå å klemme og falle for å skade fjernkontrollen;
5. Hvis den ikke er brukt på lang tid, please remove the battery and store the remote control and
battery in a clean and safe place;
6. Vær oppmerksom på fuktsikker under lagring og transport.

11.Sikkerhetsinformasjon

1. Les bruksanvisningen nøye før bruk. Non-professionals are prohibited
from operating.
2. Please use the original charger or a charger produced by a regular manufacturer with
the same specifications.
3. Please charge in time to avoid incorrect operation due to insufficient power causing
the remote control to be unresponsive.
4. Hvis reparasjon er nødvendig, vennligst kontakt produsenten. If the damage is caused by
self-repair, produsenten vil ikke gi garanti.