Crawler Wire Saw Machine Automatisk trådløs fjernkontroll DH12S-LD

Beskrivelse

Produktmodell

Modell: DH12S-LD

Gjeldende utstyr:crawler wire saw machine

Produkttilbehør Diagram

Note: Du kan velge en av de tre antennene. Sugekoppantennen er som standard standard.

Remote Control Switch Beskrivelse

Displaycontent introduction

Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

Lav spenning: Fjernkontrollbatteriet er for lavt, Vennligst bytt batteriet.

Nettverket falt: Det trådløse signalet blir avbrutt. Vennligst sjekk mottakerenes kraft, Kraft det på igjen, og start fjernkontrollen på nytt.

Instruksjoner for fjernkontrollfunksjon Operasjon

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Slå på strømbryteren, andthe display will show the motor speed, som indikerer vellykket oppstart.

2.Large motor and speed regulation

Turn the “forward/reverse” switch to forward, the receiver’s large motor will turn on, and the display will show forward

Turn the “forward/reverse” switch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse

Rotate the “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move the “forward/reverse” switch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Turn the “Forward/Reverse” switch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Turn the “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Turn the “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

I manuell modus:
Turn left in place: Press and hold the “Enable” button, turn the “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Press and hold the “Enable” button, turn the “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

I automatisk modus: press and hold the “Enable” button and rotate the “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;

7.Automatic cutting

The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: I manuell modus, press and hold the “Enable” button and rotate the “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 til 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (users are prohibited from modifying it without permission)

Noen funksjoner av fjernkontrollen kan justeres gjennom parametere. I manuell modus, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Avslutt parametermenyen: Velg å lagre eller ikke spare, then press the enable button to confirm the exit;
Maksimal strøm: the operating rated current of the cutting motor is 80% of this currentt;
Hastighetskontrollparametere: automatic cutting control parameters, misligholde 800, modification is prohibited;
Retardasjonsparameter: automatic cutting control parameter. When the cutting current change value exceeds this value,deceleration begins.
Akselerasjon A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Retting A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Begynn selvlåsing: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maksimal turgåing: the maximum speed of the small motor.
Kutte strøm: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Standard hastighetsgrense: the default maximum speed of automatic cutting speed when turning on the machine.
Automatisk modus: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Speed limit offset: the maximum speed of the small motor during automatic cutting.
Maksimal vert: maximum speed of large motor.

ELEKTRISKE ELEKTRISKE KJENTERISTIKKER

Fjernkontrollstørrelse

Den endelige tolkningsretten for dette produktet tilhører bare vårt selskap.