Descriptio
Product Model
Model: DH12S-LD
Lorem apparatu:crawler wire saw machine
Product accessiones tabulae
Nota: Vos can eligere unum ex tribus antennas. Et Suction Cup Antenna est vexillum per default.
Longinquus imperium switch descriptio
Displaycontent introduction
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Humilis voltage: Remote control altilium nimis, obsecro reponere in altilium.
Network cecidit: Et wireless signum est intermittitur. Placere reprehendo potentia recipiens, Potestatem illud iterum, et sileo in remotis imperium.
Remote control munus operandi instructiones
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Turn in virtute switch, andthe display will show the motor speed, significat prospere startup.
2.Large motor and speed regulation
Conversus “Porro / Reverse” SWITCH PRIMO, the receiver’s large motor will turn on, and the display will show forward
Conversus “Porro / Reverse” MANCEPS, the large motor of the receiver will turn on in reverse, and the display will show reverse
Rotate “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “Porro / Reverse” SWITCH PRIMO, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Conversus “Porro / Reverse” MANCEPS, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Conversus “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Conversus “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
In manual modus:
Turn left in place: Torcular et tenere “Enable” button, conversus “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Torcular et tenere “Enable” button, conversus “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” button et gyrari “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.CAECORUM
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In manual modus, press and hold the “Enable” button et gyrari “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 ut 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (users prohibentur ab modifinging eam sine permission)
Munera quaedam ditionis remotae per parametros adaptari possunt. In manual modus, when the small motor speed S2 is 10, ventilabis deinceps / vicissim switch ter in ordine, and then push it down three times in a row to enter the parameter menu;
Exit parametri menu: eligere nisi salvare, then press the enable button to confirm the exit;
Maximus current: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, default 800, mutatio est prohibitus;
Torus parameter: automatic cutting control parameter. Cum cutting current mutatio valorem excedit hoc valore,deceleration begins.
Acceleratio A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
A2 torpet: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximum ambulans: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Celeritate terminum offset: the maximum speed of the small motor during automatic cutting.
Maximum exercitum: maximum speed of large motor.
Remota imperium electrica characteres
Remota imperium magnitudine
In ultima interpretatio ius huius productum pertinet solum ad nostram turma.
