크롤러 와이어 톱 기계 자동 무선 원격 제어 DH12S-LD

기술

제품 모델

모델: DH12S-LD

적용 가능한 장비:crawler wire saw machine

제품 액세서리 다이어그램

메모: 세 가지 안테나 중 하나를 선택할 수 있습니다.. 흡입 컵 안테나는 기본적으로 표준입니다..

원격 제어 스위치 설명

디스플레이 콘텐츠 소개

Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (매개변수 조정 가능)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

낮은 전압: 리모컨 배터리가 너무 부족해요, 배터리를 교체해 주세요.

네트워크가 끊어졌습니다.: 무선 신호가 중단되었습니다.. 수신기의 전원을 확인하십시오., 다시 켜봐, 그리고 리모콘을 다시 시작해 보세요.

리모콘 기능 작동 지침

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, 전원 스위치를 켜 줘, andthe display will show the motor speed, 성공적인 시작을 나타내는.

2.Large motor and speed regulation

켜다 “정방향/역방향” 앞으로 전환, the receiver’s large motor will turn on, and the display will show forward

켜다 “정방향/역방향” 역방향으로 전환하다, the large motor of the receiver will turn on in reverse, and the display will show reverse

회전 “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move the “정방향/역방향” 앞으로 전환, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

켜다 “정방향/역방향” 역방향으로 전환하다, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

켜다 “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left

켜다 “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

수동 모드에서:
Turn left in place: 길게 누르세요. “Enable” button, 켜다 “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: 길게 누르세요. “Enable” button, 켜다 “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

In automatic mode: press and hold the “Enable” 버튼을 누르고 회전하세요. “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;

7.자동 절단

The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: 수동 모드에서, press and hold the “Enable” 버튼을 누르고 회전하세요. “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 to 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (사용자는 이를 무단으로 수정하는 것을 금지합니다.)

Some functions of the remote control can be adjusted through parameters. 수동 모드에서, when the small motor speed S2 is 10, 정방향/역방향 스위치를 연속으로 3회 위로 누릅니다., and then push it down three times in a row to enter the parameter menu;
매개변수 메뉴 종료: choose to save or not save, then press the enable button to confirm the exit;
최대 전류: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, 기본 800, 수정은 금지되어 있습니다;
감속 매개변수: automatic cutting control parameter. 절단 전류 변화 값이 이 값을 초과하는 경우,deceleration begins.
가속도 a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
감속 a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
최대 걷기: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
속도 제한 오프셋: the maximum speed of the small motor during automatic cutting.
최대 호스트: maximum speed of large motor.

원격 제어 전기적 특성

리모콘 크기

본 제품의 최종 해석권은 당사에 있습니다..