ક્રાઉલર વાયર મશીન ઓટોમેટિક વાયરલેસ રીમોટ કંટ્રોલ DH12S-LD જોયું

ઘર|ઔદ્યોગિક રીમોટ કંટ્રોલ|ક્રાઉલર વાયર મશીન ઓટોમેટિક વાયરલેસ રીમોટ કંટ્રોલ DH12S-LD જોયું

ક્રાઉલર વાયર મશીન ઓટોમેટિક વાયરલેસ રીમોટ કંટ્રોલ DH12S-LD જોયું

અરજી:ક્રોલર વાયર સો મશીન માટે ખાસ વપરાય છે

1.સ્વચાલિત કટીંગ મોડને સપોર્ટ કરે છે, મોટી મોટર વર્તમાન અનુસાર નાની મોટરની ચાલવાની ઝડપને આપમેળે ગોઠવે છે, અને આપોઆપ કટીંગ નિયંત્રણ પ્રાપ્ત કરે છે.

2.અવરોધ-મુક્ત ટ્રાન્સમિશન અંતર છે 200 મીટર.

3. મોટી મોટરો અને નાની મોટરો માટે ડ્યુઅલ સ્પીડ રેગ્યુલેશનને સપોર્ટ કરે છે.

4. નાની મોટરને સ્થાને ટર્નિંગને સપોર્ટ કરો.

5. ડાબી અને જમણી વ્હીલ નાની મોટર રેખીય કરેક્શનને સપોર્ટ કરે છે.


  • ઓછી વીજ વપરાશની ડિઝાઇન
  • વાપરવા માટે સરળ

વર્ણન

Product model

મોડલ: DH12S-LD

Applicable equipment:crawler wire saw machine

Product accessories diagram

નૉૅધ: You can choose one of the three antennas. The suction cup antenna is standard by default.

Remote control switch description

Displaycontent introduction

Large motor speedS1:0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

Low voltage: The remote control battery is too low, please replace the battery.

Network dropped: The wireless signal is interrupted. Please check the power of the receiver, power it on again, and restart the remote control.

Remote control function operation instructions

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, turn on the power switch, andthe display will show the motor speed, indicating successful startup.

2.Large motor and speed regulation

Turn theforward/reverseswitch to forward, the receiver’s large motor will turn on, and the display will show forward

Turn theforward/reverseswitch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse

Rotate thelarge motor speed adjustmentknob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move theforward/reverseswitch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Turn theForward/Reverseswitch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Turn theLeft/Rightswitch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Turn theturn left/rightswitch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

In manual mode:
Turn left in place: Press and hold theEnablebutton, turn theLeft/Right Turnswitch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Press and hold theEnablebutton, turn theLeft/Right Turnswitch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

In automatic mode: press and hold theEnablebutton and rotate theSmall Motor Speed Adjustmentto adjust the maximum speed of the small motor during automatic cutting;

7.Automatic cutting

The first step is to start the big motor; the second step is to switch the mode switch toAuto”; the third step is to start the small motor and the screen will displayCutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In manual mode, press and hold theEnablebutton and rotate theSmall Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 to 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (users are prohibited from modifying it without permission)

Some functions of the remote control can be adjusted through parameters. In manual mode, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Exit the parameter menu: choose to save or not save, then press the enable button to confirm the exit;
Maximum current: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, default 800, modification is prohibited;
Deceleration parameter: automatic cutting control parameter. When the cutting current change value exceeds this value,deceleration begins.
Acceleration a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Deceleration a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximum walking: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Speed limit offset: the maximum speed of the small motor during automatic cutting.
Maximum host: maximum speed of large motor.

Remote control electrical characteristics

Remote control size

The final interpretation right of this product belongs only to our company.

સ્પષ્ટીકરણ પરિમાણ

Wixhc ટેકનોલોજી

અમે CNC ઉદ્યોગમાં અગ્રણી છીએ, કરતાં વધુ માટે વાયરલેસ ટ્રાન્સમિશન અને CNC મોશન કંટ્રોલમાં વિશેષતા 20 વર્ષો. અમારી પાસે ડઝનેક પેટન્ટ ટેક્નોલોજી છે, અને અમારા ઉત્પાદનો કરતાં વધુમાં સારી રીતે વેચાય છે 40 વિશ્વભરના દેશો, લગભગ ની લાક્ષણિક એપ્લિકેશનો એકઠી કરવી 10000 ગ્રાહકો.

તાજેતરની ટ્વીટ્સ

ન્યૂઝલેટર

નવીનતમ સમાચાર અને અપડેટ માહિતી મેળવવા માટે સાઇન અપ કરો. ચિંતા કરશો નહીં, અમે સ્પામ મોકલીશું નહીં!