Beschreibung
Produktmodell
Modell: DH12S-LD
Anwendbare Ausrüstung:crawler wire saw machine
Produktzubehör Diagramm
Notiz: Sie können eine der drei Antennen auswählen. Die Saugnapfantenne ist standardmäßig Standard.
Beschreibung des Fernbedienungsschalters
Displaycontent introduction
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Niederspannung: Die Batterie der Fernbedienung ist zu schwach, Bitte tauschen Sie die Batterie aus.
Netzwerk unterbrochen: Das Funksignal ist unterbrochen. Bitte überprüfen Sie die Leistung des Empfängers, schalten Sie es wieder ein, und starten Sie die Fernbedienung neu.
Bedienungsanleitung für die Fernbedienungsfunktion
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Schalten Sie den Netzschalter ein, andthe display will show the motor speed, zeigt einen erfolgreichen Start an.
2.Large motor and speed regulation
Turn the “forward/reverse” switch to forward, the receiver’s large motor will turn on, and the display will show forward
Turn the “forward/reverse” switch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse
Rotate the “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “forward/reverse” switch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Turn the “Forward/Reverse” switch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Turn the “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Turn the “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
Im manuellen Modus:
Turn left in place: Press and hold the “Enable” button, turn the “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Press and hold the “Enable” button, turn the “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
Im Automatikmodus: press and hold the “Enable” button and rotate the “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Automatic cutting
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: Im manuellen Modus, press and hold the “Enable” button and rotate the “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 Zu 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (users are prohibited from modifying it without permission)
Einige Funktionen der Fernbedienung können über Parameter angepasst werden. Im manuellen Modus, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Verlassen Sie das Parametermenü: Wählen Sie „Speichern“ oder „Nicht speichern“., then press the enable button to confirm the exit;
Maximaler Strom: the operating rated current of the cutting motor is 80% of this currentt;
Geschwindigkeitskontrollparameter: automatic cutting control parameters, Standard 800, modification is prohibited;
Verzögerungsparameter: automatic cutting control parameter. When the cutting current change value exceeds this value,deceleration begins.
Beschleunigung a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Verzögerung a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Beginnen Sie mit der Selbsthemmung: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximales Gehen: the maximum speed of the small motor.
Schneidstrom: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Standardgeschwindigkeitsbegrenzung: the default maximum speed of automatic cutting speed when turning on the machine.
Automatikmodus: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Tempolimit-Offset: the maximum speed of the small motor during automatic cutting.
Maximaler Host: maximum speed of large motor.
Elektrische Eigenschaften der Fernbedienung
Größe der Fernbedienung
Das endgültige Auslegungsrecht dieses Produkts liegt allein bei unserem Unternehmen.
