Mašina za gusjeničarsku žičanu pilu sa automatskim bežičnim daljinskim upravljanjem DH12S-LD

Dom|industrijski daljinski upravljač|Mašina za gusjeničarsku žičanu pilu sa automatskim bežičnim daljinskim upravljanjem DH12S-LD

Mašina za gusjeničarsku žičanu pilu sa automatskim bežičnim daljinskim upravljanjem DH12S-LD

Aplikacija:Posebno se koristi za gusjeničarsku žičanu pilu

1.Supports automatic cutting mode, automatically adjusts the walking speed of the small motor according to the large motor current, and achieves automatic cutting control.

2.Udaljenost prijenosa bez prepreka je 200 metara.

3. Supports dual speed regulation for large motors and small motors.

4. Support small motor turning in place.

5. Supports left and right wheel small motor linear correction.


  • Dizajn male potrošnje energije
  • Jednostavan za korištenje

Opis

Model proizvoda

Model: DH12S-LD

Primjenjiva oprema:crawler wire saw machine

Dijagram pribora proizvoda

Bilješka: Možete odabrati jednu od tri antene. Antena na usisnoj čaši je standardno standardna.

Opis prekidača za daljinsko upravljanje

Displaycontent introduction

Large motor speedS1:0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

Nizak napon: Baterija daljinskog upravljača je preniska, molimo zamijenite bateriju.

Mreža je pala: Bežični signal je prekinut. Molimo provjerite snagu prijemnika, ponovo ga uključite, i ponovo pokrenite daljinski upravljač.

Upute za rad funkcije daljinskog upravljača

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, uključite prekidač za napajanje, andthe display will show the motor speed, što ukazuje na uspješno pokretanje.

2.Large motor and speed regulation

Turn theforward/reverseswitch to forward, the receiver’s large motor will turn on, and the display will show forward

Turn theforward/reverseswitch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse

Rotate thelarge motor speed adjustmentknob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move theforward/reverseswitch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Turn theForward/Reverseswitch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Turn theLeft/Rightswitch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Turn theturn left/rightswitch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

In manual mode:
Turn left in place: Press and hold theEnablebutton, turn theLeft/Right Turnswitch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Press and hold theEnablebutton, turn theLeft/Right Turnswitch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

In automatic mode: press and hold theEnablebutton and rotate theSmall Motor Speed Adjustmentto adjust the maximum speed of the small motor during automatic cutting;

7.Automatic cutting

The first step is to start the big motor; the second step is to switch the mode switch toAuto”; the third step is to start the small motor and the screen will displayCutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In manual mode, press and hold theEnablebutton and rotate theSmall Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 to 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (users are prohibited from modifying it without permission)

Neke funkcije daljinskog upravljača mogu se podesiti kroz parametre. In manual mode, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Izađite iz menija parametara: odaberite da sačuvate ili ne sačuvate, then press the enable button to confirm the exit;
Maximum current: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, default 800, modification is prohibited;
Deceleration parameter: automatic cutting control parameter. When the cutting current change value exceeds this value,deceleration begins.
Acceleration a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Deceleration a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximum walking: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Speed limit offset: the maximum speed of the small motor during automatic cutting.
Maximum host: maximum speed of large motor.

Električne karakteristike daljinskog upravljača

Veličina daljinskog upravljača

Pravo konačnog tumačenja ovog proizvoda pripada samo našoj kompaniji.

Parametar specifikacije

Wixhc tehnologija

Mi smo lider u CNC industriji, specijalizirao se za bežični prijenos i CNC kontrolu upravljanja za više od 20 godina. Imamo desetine patentiranih tehnologija, a naši proizvodi se prodaju više od 40 zemalja širom svijeta, gomilajući tipične aplikacije od skoro 10000 kupaca.

Nedavni tweetovi

Bilten

Prijavite se za dobivanje najnovijih vijesti i ažuriranja podataka. Ne brini, nećemo poslati neželjenu poštu!