Аўтаматычнае бесправадное дыстанцыйнае кіраванне гусенічнай драцяной пілы DH12S-LD

Дадому|прамысловы пульт дыстанцыйнага кіравання|Аўтаматычнае бесправадное дыстанцыйнае кіраванне гусенічнай драцяной пілы DH12S-LD

Аўтаматычнае бесправадное дыстанцыйнае кіраванне гусенічнай драцяной пілы DH12S-LD

Ужыванне:Specially used for crawler wire saw machine

1.Supports automatic cutting mode, automatically adjusts the walking speed of the small motor according to the large motor current, and achieves automatic cutting control.

2.Безбар'ерная адлегласць перадачы 200 метраў.

3. Supports dual speed regulation for large motors and small motors.

4. Support small motor turning in place.

5. Supports left and right wheel small motor linear correction.


  • Дызайн нізкага энергаспажывання
  • Просты ў выкарыстанні

Апісанне

Мадэль прадукту

Мадэль: DH12S-LD

Прыдатнае абсталяванне:crawler wire saw machine

Схема аксэсуараў вырабы

Нататка: Вы можаце выбраць адну з трох антэн. Антэна-прысоска стандартная па змаўчанні.

Апісанне пераключальніка дыстанцыйнага кіравання

Displaycontent introduction

Large motor speedS1:0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

Нізкае напружанне: Батарэя дыстанцыйнага кіравання занадта нізкая, калі ласка, заменіце батарэю.

Сетка адключана: Бесправадны сігнал перарываецца. Калі ласка, праверце магутнасць прымача, уключыце яго зноў, і перазапусціце пульт дыстанцыйнага кіравання.

Інструкцыя па эксплуатацыі функцыі дыстанцыйнага кіравання

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, уключыце выключальнік, andthe display will show the motor speed, паказвае паспяховы запуск.

2.Large motor and speed regulation

Turn theforward/reverseswitch to forward, the receiver’s large motor will turn on, and the display will show forward

Turn theforward/reverseswitch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse

Rotate thelarge motor speed adjustmentknob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move theforward/reverseswitch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Turn theForward/Reverseswitch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Turn theLeft/Rightswitch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Turn theturn left/rightswitch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

In manual mode:
Turn left in place: Press and hold theEnablebutton, turn theLeft/Right Turnswitch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Press and hold theEnablebutton, turn theLeft/Right Turnswitch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

In automatic mode: press and hold theEnablebutton and rotate theSmall Motor Speed Adjustmentto adjust the maximum speed of the small motor during automatic cutting;

7.Automatic cutting

The first step is to start the big motor; the second step is to switch the mode switch toAuto”; the third step is to start the small motor and the screen will displayCutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: In manual mode, press and hold theEnablebutton and rotate theSmall Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 каб 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (users are prohibited from modifying it without permission)

Некаторыя функцыі пульта дыстанцыйнага кіравання можна наладзіць праз параметры. In manual mode, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Выйдзіце з меню параметраў: выбраць, захоўваць ці не захоўваць, then press the enable button to confirm the exit;
Maximum current: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, default 800, modification is prohibited;
Deceleration parameter: automatic cutting control parameter. When the cutting current change value exceeds this value,deceleration begins.
Acceleration a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Deceleration a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximum walking: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Speed limit offset: the maximum speed of the small motor during automatic cutting.
Maximum host: maximum speed of large motor.

Электрычныя характарыстыкі пульта дыстанцыйнага кіравання

Памер пульта дыстанцыйнага кіравання

Права канчатковай інтэрпрэтацыі гэтага прадукта належыць толькі нашай кампаніі.

Спецыфікацыйны параметр

Wixhc Technology

Мы лідзіруем у галіне ЧПУ, спецыялізуецца на бесправадной перадачы і кіраванні рухамі з ЧПУ больш чым 20 гадоў. У нас ёсць дзясяткі запатэнтаваных тэхналогій, і нашы прадукты добра прадаюцца больш 40 краін усяго свету, назапашваючы амаль тыповыя прыкладання 10000 пакупнікі.

Апошнія твіты

Рассылка

Падпішыцеся, каб атрымаць апошнія навіны і абнавіць інфармацыю. Не хвалюйцеся, мы не будзем адпраўляць спам!